 |
 |
|
|
 หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Development of a Wear Testing Machine for Dental Crown Application) ผู้เขียน: Panya Aroonjarattham,  นายชาคริต สุวรรณจำรัส, อาจารย์ , เอกชัย ชัยชนะศิริ สื่อสิ่งพิมพ์:pdf AbstractA three axes wear testing machine for a dental crown was developed for human tooth application. There were two main sections of the controllers: the application of an AC servomotor (Z-axis) for creating and controlling the force which is used in testing and the application of a step motor (X-axis and Y-axis) for creating and controlling the motion. This study aimed to compare the ability of the controlling force of the AC servomotor on two different surfaces—a smooth fl at surface and a dental crown surface. Three testing cases were considered at frequencies of 0.5, 0.75, and 1 Hz in a range of motion of 1 mm: 1) simulating the force of chewing (0–60 N) and the motion of a circular process, 2) simulating a constant force (60 N) of one way movement in a circular process and 3) simulating a constant force (60 N) of the reciprocating movement in a circular process. The machine was tested using a dental crown, which was made of zirconia, by simulating the force, the motion and the various conditions of the teeth in the oral cavity. The force which occurred in all three axes was measured by the load cell. According to the experiment, the AC servomotor was able to control the force exerted on two different surfaces with nearly similar results. The average force errors on the smooth surface and the dental crown surface were 13.70 and 13.82%, respectively. The root mean square errors of the smooth surface and the dental crown surface were 17.47 and 16.99, respectively. |
หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Diffusion Jet Flame Models Using Open Source Code CFD Software) ผู้เขียน:นายชาคริต สุวรรณจำรัส, อาจารย์, Panya Aroonjarattham สื่อสิ่งพิมพ์:pdf AbstractOpen-source code software (OpenFOAM) based on computational fluid dynamics (CFD) was implemented and applied to simulate the diffusion of a jet flame. The large eddy simulation (LES) of the turbulence combustion model was written using the C++ language. The mixture fraction approach, an infinitely-fast chemistry assumption and radiative heat transfer were combined with this LES model. The finite volume method was performed to solve and simulate diffusion jet flame models under varying methane flow rates and environmental pressures. The results of the jet flame simulation comprising the percentage of maximum burning temperature, the heat release rate and oxygen from the oxygen fraction were defined to be the flame shape for validation with experiments. It was found that the flame length measured using the heat release rate from the results of simulations had the best agreement with the experiments. An average error of less than 5.84% was obtained by a comparison between the developed CFD model and the experiment when the CFD flame length was depicted by the heat release rate. |
|
 |
|
|
หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Finite Element Method for Creep Testing of High Density Polyethylene Lubricant Oil Bottles) ผู้เขียน:นายชาคริต สุวรรณจำรัส, อาจารย์, เอกชัย ชัยชนะศิริ สื่อสิ่งพิมพ์:pdf AbstractStacking is one method for storing many lubricant oil bottles. Bottles on the lower storey may collapse after storage for a long time because of the creep behavior of bottle materials. To avoid bottle collapse, creep testing of the bottle is required to obtain the relation between deformation and the time a bottle is under creep load. This relation can be used to manage the storage time and to improve bottle shape. Unfortunately, the identification of creep resistance for lubricant oil bottles may take more than one month. This is not satisfactory considering the market competition for container products. Therefore, this study used the finite element method (FEM) to simulate the creep behavior of high density polyethylene (HDPE) lubricant oil bottles and compared the experimental results to validate the FEM. Sample 1 L and 6 L bottles with masses of 55 and 310 g, respectively, were tested and simulated. From the results, the overall difference of deformation between the FEM and experimental samples for the 1 L and 6 L bottles was 16.20 and 13.91%, respectively. However, the FEM was able to capture the trend of bottle deformation. The weak points of 1 L and 6 L bottles were the shoulder and the handle of the bottle, respectively. The FEM results can be applied to manage the storage time of lubricant oil with regard to stacking and to developing the design of the lubricant oil bottle as well. |
หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Determination of Drop-Impact Resistance of Plastic Bottles using Computer Aided Engineering) ผู้เขียน:นายชาคริต สุวรรณจำรัส, อาจารย์, ดร.ธำรงค์ พุทธาพิทักษ์ผล, รองศาสตราจารย์ สื่อสิ่งพิมพ์:pdf AbstractASTM D2463 discusses the standard test method for drop impact resistance of blow-molded thermoplastic containers using procedures to determine the mean failure height and the standard deviation of the distribution. Unfortunately, costly prototypes have to be created before the drop impact test can be conducted. The MSC Dytran program was used with finite element simulation of the drop impact test of plastic bottles to determine the failure height for polyethylene terephthalate (PET) and high density polyethylene (HDPE) bottles. The finite element results were verified using experimental results obtained using the test method prescribed in ASTM D2463. It was found that the finite element simulation obtained accurate results. The failure heights for the PET and HDPE bottles were 4.53 ? 0.41 m and 4.65 ? 0.81 m, respectively. The errors in the failure height obtained from the FE simulation were less than 9.27% for the PET bottle and 5.59% for the HDPE bottle. |
|
|
หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Effect of Mechanical Axis on Strain Distribution after Total Knee Replacement) ผู้เขียน:Panya Aroonjarattham, Kitti Aroonjarattham, นายชาคริต สุวรรณจำรัส, อาจารย์ สื่อสิ่งพิมพ์:pdf AbstractA total knee replacement is one of the most successful orthopedic procedures to enable the patient’s return to a normal, active lifestyle. The angle of the mechanical axis depends on the surgeon’s decision, which effects the strain distribution on the femoral bone and may lead to a fracture of the femur . This study evaluated the equivalent total strain on the femoral shaft under daily activities using various models of the lower extremity with a varus knee deformity and the lower extremity with a total knee prosthesis, which was inserted at five different angles—0?, 3? valgus, 5? valgus, 3? varus and 5? varus. The results showed that the insertion of a total knee replacement in the case of a bowleg helped to reduce the equivalent total strain on the bone. The position of the prosthesis with a 3? valgus angle produced less strain distribution on the femoral bone. From the results, the mechanical axis affected the risk of the bone fracture. Considering the plastic spacer, it was found that there was an increase in the von Mises stress in the medial side of the model leg with a knee prosthesis of 3? valgus . |
หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Simulation of Three Dimensional Liquid-Sloshing Models using C++ Open Source Code CFD Software) ผู้เขียน:เอกชัย ชัยชนะศิริ, นายชาคริต สุวรรณจำรัส, อาจารย์ สื่อสิ่งพิมพ์:pdf AbstractThe open source computational fl uid dynamic (CFD) codes—open fi eld operation and manipulation (OpenFOAM)—were developed to simulate the three dimensional sloshing of liquid inside moving rectangular tanks. Equations governing the two-phases of fl uid were used in these simulations and the Volume of Fluid method was used to capture the free surface of the liquid sloshing. The fi nite volume method was used to solve these problems. The solutions of the simulations were validated using experiment results based on the free surface height and the pressure developed on the wall of the tanks. It was found that the average error of the surface height and the pressure obtained from the simulations were 2.33% and 6.65%, respectively. |
หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Analysis of Fluid-Structure Interaction Effects of Liquid-Filled Container under Drop Testing) ผู้เขียน:นายชาคริต สุวรรณจำรัส, อาจารย์, ดร.ธำรงค์ พุทธาพิทักษ์ผล, รองศาสตราจารย์, สัจจาทิพย์ ทัศนียพันธุ์ สื่อสิ่งพิมพ์:pdf AbstractAn analysis of drop-impact test for plastic containers is a first step toward the simulation of impact events for design and development purposes. Computer methods based on finite element analysis (FEA) were able to predict the performance of liquid-filled plastic containers to withstand drop-impact loading without rupture. This paper presented results of finite element analysis studied drop-test of liquid-filled plastic bottles. The aim of this study was to determine the accuracy of a non-linear explicit FE code in the MSC.Dytran program, by comparing FEA results to experiments. This paper is to lay down the effective procedures for analyzing the drop-test using FEA, which are appropriate for the design and development of plastic containers. |
 |
หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : The k-? Turbulence Model to Simulate the Two-Phase Flows of Fluids in Flumes using C++ Open Source Code Computational Fluid Dynamic Software) ผู้เขียน:เอกชัย ชัยชนะศิริ, นายชาคริต สุวรรณจำรัส, อาจารย์ สื่อสิ่งพิมพ์:pdf AbstractThe governing equations of two-phase flows based on the k-? turbulence model were developed using open source computational fluid dynamic codes and open field operation and manipulation (OpenFOAM) software to simulate water flows in a flume. The water surface was modeled using the volume of fluid method with a turbulence model. The PISO (pressure implicit with splitting of operator) algorithm was used to solve the pressure-velocity coupling in the two-phase flows. The solutions of the simulations were validated using the experimental results as free surface profiles on the wall of the laboratory flume in transient and steady time periods. The transient time period started from when the water was distributed into the flume until it began to overflow the top of the weirs. The steady time period accounted for the water overflowing the weirs and the surface profiles did not change. It was found that the average error of the surface profiles in the transient and steady time periods obtained from the simulations was 8.94% and 8.06%, respectively. |
ที่มา:สำนักงานกองทุนสนับสนุนการวิจัยหัวเรื่อง:เครื่องมือวัดการเคลื่อนที่ของผิวของเหลวภายในภาชนะบรรจุของเหลวที่ถูกกระตุ้น หัวหน้าโครงการ:นายชาคริต สุวรรณจำรัส, อาจารย์ |